Filter

SuperCAT4+ Pipe Cable Locator

SuperCAT4+ Cable Avoidance Tool.

Range of locators and transmitters designed to target specific buried assets.

Buying Guide: Identify your application. 2. Choose a suitable locator and T1 transmitter. You may opt for additional accessories for your locating needs. See the configuration options table below for reference.

ADD ON:

+ More Locator Accessories

SuperCAT4+ Cable Avoidance Tool for Ground Work Contractor

The SuperCAT4+ range of locators and transmitters are an expansion from the earlier Radiodetection’s C.A.T family.

With a wide selection of passive, sonde and active frequencies designed to target specific buried assets, it is a must have tool for contractor dealing with underground work. It is a simple tool yet give operators the feature needed and with minimal training.

SuperCAT+ Configuration Options:

Locate pipelines protected by a Cathodic Protection

SuperCAT+ CPS

Tailored with CPS feature, the SuperCAT+ CPS is suitable for oil and gas pipes using a Cathodic Protection System. The CPS model can locate the rectified signal without needing an additional transmitter.

Find water and drain pipes

SuperCAT+S

The SuperCAT+S model are designed to locates a range of sonde frequencies that can be a challenges when finding water or drain pipes. A lower frequency sonde is useful to trace deep cast-iron pipes. Higher frequency sondes can be easier to distinguish in an electronically noisy urban environment.

Detect a broad range of utilities

SuperCAT4+ can be used to locate a comprehensive set of active frequencies to support the detection and tracing of different cable types in varied environmental conditions. Higher frequencies such as the 131kHz or 65kHz can be used to find well-insulated utilities such as twisted-pair telecom cables or insulated pipe joints. For long range locating of lower resistance cables, such as power lines, lower frequency options are available.

For more information on how a cable and pipe locator works, please refer to our Theory On Locating Buried Pipe guidance link here.

SuperCAT4+	10/SuperCAT4+, 10/SuperCAT4+S, 10/SuperCAT4+CPS, 10/T1-SUPERCAT4+131, 10/T1-SUPERCAT4+640, 10/T1-SUPERCAT4+640/65, 10/T1-BAG

Features

Safety Built-In

All SuperCAT4+ models come with a range of features designed to aid safe working practices.

Dynamic Overload Protection

High levels of electrical interference, as found around substations and near high-voltage transmission cables can overload sensitive electronics. Dynamic Overload Protection filters this interference out, enabling SuperCAT4+ to continue locating where other units struggle.

Dig more safely with StrikeAlert™

StrikeAlert warns the user to the possible presence of shallow cables and utility lines in both Power and Active Line modes. Although work practices and guidelines insist power cables are buried below a certain depth, a common cause of cable strikes is unexpectedly shallow cables.

TruDepth™

Indicates depth when the locator is oriented correctly above the target cable, pipe or sonde for the most accurate reading.

Real Sound

The audio signals emitted by the SuperCAT4+ are derived from the signals detected. Radio, Power and Active signals can be easily distinguished from each other, and from background noise, helping identification of target utilities, and aiding differentiation of closely co-located utilities.

Application

Locate pipelines protected by a Cathodic Protection System

Optimized for metal pipes including those that use rectified currents as part of their Cathodic Protection System. The CPS signal can be located and traced without the need to apply an additional transmitter signal to the pipeline * Choose between M (Metric) or I (Imperial) locator models ** Power frequency and corresponding active low frequency set by model , (50Hz – 640Hz and 60Hz – 512 Hz)

Find water and drain pipes

SuperCAT4+S and T1-512/640

For the challenge of detecting and tracing buried pipes, the SuperCAT4+ S locates the widest range of sonde frequencies. Additionally, an active 33kHz frequency can be applied to a Flexitrace using a T1-512/640 for continuous signal tracing. *Choose between M (Metric) or I (Imperial locator Models ** Power frequency and corresponding active low frequency set by model, (50Hz – 640Hz and 60Hz – 512 Hz)

Detect a broad range of utilities

SuperCAT4+ and T1 Range

Designed to meet the demanding environments of the construction industry, this multi-utility locator can be used with a wide range of sondes and accessories. SuperCAT4+ is compatible with all T1 Transmitters. Higher frequency transmitters are recommended for high-impedance cables. Lower frequency signals travel further on lower-impedance services. *Choose between M (Metric) or I (Imperial locator Models ** Power frequency and corresponding active low frequency set by model, (50Hz – 640Hz and 60Hz – 512 Hz